Mallory-ignition Mallory PROMASTER SERIES 85551m_8361m_8360m Manuel d'utilisateur télécharger pdf

1MALLORY TECHNICAL SUPPORT (216) 688-8300

PROMASTER

SERIES

INSTALLATION INSTRUCTIONS

FORM INST85551M 12/09

HOW TO INSTALL THE DISTRIBUTOR

1. If the distributor to be replaced has not already been

removed from the engine, remove its cap. Do not

remove the spark plug wires at this time.

2. Crank the engine slowly until the rotor blade aims at

a fixed point on the engine or firewall. Note this point

for future reference.

3. Unplug all external connectors coming from the

distributor.

4. Now put the existing cap back on and note and mark

which spark plug wire the rotor (blade) is pointing at.

Then number the wires according to cylinder and

remove the wires. If in doubt you can leave the wires

connected to the old cap and transfer them to the

new cap and distributor later in the process (see

point # 9).

5. Loosen and remove the distributor hold-down bolt

and clamp. Lift the old distributor out. At this point

the rotor may spin and move from its position. This

is because of the distributor gear.

6. Lower the new distributor into position. The rotor

should be aimed at the same fixed point as was the

rotor from the old distributor. After the new distributor

has been lowered into place, you may find that it

hasn't seated firmly against the intake manifold. This

indicates that the lower end of the distributor shaft is

not properly aligned with the oil pump drive rod. Do

not attempt to force the distributor into position.

7. Install the gasket using plenty of the supplied lubricant.

8. Reinstall the hold-down clamp and thread the bolt

just enough to exert a very slight pressure against the

distributor. If the distributor was not firmly seated,

manually rotate the engine until the distributor drops

down into place.

9. With the distributor properly seated, tighten the hold-

down bolt just enough so that the distributor is held

in place, but can still be rotated with a little effort.

10. Remove the plug wires one at a time from the old

cap and install them in the corresponding positions

of the new cap. After all wires have been transferred,

verify that the wire in the terminal post that is aligned

with the rotor leads to number one cylinder. If you

are unsure of cylinder number position or firing

order, this information can be found in the service

manual that covers your particular engine. Put on

the distributor cap.

11. Reconnect the wiring lead from the distributor to the

ignition switch. At this time you can begin timing.

1 – Machined Chevy V8 Distributor

1 - Rotor,

1 - Distributor Cap

1 - Wire Retainer

2 - 1.5" Self Tapping Screws

1 - Advance Kit

1 - Gasket

1 - Tube of Gear Lubricant

2 - O-Rings

1 - Vacuum Advance Lock-Out Kit (if equipped with

vacuum advance)

Included with the distributor:

PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLING.

You should always disconnect the battery, negative lead first, before working on the ignition system. When you are

done reconnect the battery installing the negative lead first.

1 2

Résumé du contenu

Page 1 - PROMASTER

1MALLORY TECHNICAL SUPPORT (216) 688-8300PROMASTER®SERIESINSTALLATION INSTRUCTIONSFORM INST85551M 12/09HOW TO INSTALL THE DISTRIBUTOR1. If the distrib

Page 2 - 216.688.8300 FAX 216.688.8306

2 MALLORY IGNITION www.malloryperformance.com2FORM INST85551M 12/09Printed in U.S.A.MALLORY IS A DIVISION OF PRESTOLITE PERFORMANCE10601 MEMPHIS AVE.

Commentaires sur ces manuels

Pas de commentaire

Mallory-ignition Mallory PROMASTER SERIES 85551m_8361m_8360m Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Mallory-ignition Mallory PROMASTER SERIES 85551m_8361m_8360m. Mallory Ignition Mallory PROMASTER SERIES 85551m_8361m_8360m User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Mallory-ignition Mallory PROMASTER SERIES 85551m_8361m_8360m