Mallory-ignition Mallory UNILITE DISTRIBUTOR 576 Manuel d'utilisateur télécharger pdf

UNILITE

DISTRIBUTOR FOR

1952-70 HARLEY DAVIDSON

SPORTSTER

MOTORCYCLES

PART NO. 576

NOTE: THIS DISTRIBUTOR WILL ALSO FIT 1930-73 FLATHEAD (45 AND UL).

INSTALLATION INSTRUCTIONS

FORM 1479 (REV. B) 08/03

GENERAL INFORMATION

Any coil or combination of coils with a total primary

resistance of at least 2.0 ohms can be used with this

distributor. We recommend a 2-3 ohm coil for racing

and a 3-4 ohm coil for street use. A coil with 4-5 ohms

resistance may be used. However, performance

may be reduced, even in street applications.

NOTE: Check the charging system and make sure

that it is producing no more than 16 volts.

We recommend a spark plug gap of .040" when using

a 2-3 ohm coil. A gap of .030" is recommended when

using a 3-4 ohm coil.

An optional spring kit (PN 29014) is available for this

distributor. The kit gives you a choice of 14 different

advance curve settings.

INSTALLATION

Step 1

Turn the ignition switch to the off position. With the

point distributor still in place and correctly timed,

rotate the engine until the points begin to open on

the front cylinder lobe. The front cylinder lobe is the

narrower of the two.

If the point distributor is not installed, rotate the engine

to the beginning of the compression stroke. Locate the

timing hole. Continue rotating the engine until the

advance mark is visible through the timing hole.

Step 2

Remove the ground cable from the battery. Remove

the point wire at the coil. Remove the point distributor.

MALLORY TECHNICAL SUPPORT (775) 882-6600 Visit us on the web at: www.mrgasket.com

IMPORTANT

A 1952-70 Sportster

DISTRIBUTOR CLAMP (ORIGINAL OR AFTERMARKET) IS REQUIRED

TO INSTALL THIS DISTRIBUTOR. BECAUSE THE UNILITE

MODULE USED WITH THIS

DISTRIBUTOR REQUIRES 7-16 VOLTS, A 12 VOLT ELECTRICAL SYSTEM IS ALSO REQUIRED.

FIGURE A

HOUSING

ADAPTER RING

STANDOFF

SCREW

SLEEVE NUT

SHAFT

SET SCREW

COVER

UNILITE PLATE ASSY

SHUTTER WHEEL

GROMMET

YH ADVANCE

O-RING

GEAR

ROLL PIN

WASHER

CONNECTOR

1 2 3

Résumé du contenu

Page 1 - MOTORCYCLES

1UNILITE®DISTRIBUTOR FOR 1952-70 HARLEY DAVIDSON®SPORTSTER®MOTORCYCLESPART NO. 576NOTE: THIS DISTRIBUTOR WILL ALSO FIT 1930-73 FLATHEAD (45 AND UL).IN

Page 2 - DUAL PLUG HEADS

MALLORY IGNITION 550 MALLORY WAY, CARSON CITY, NV 897012Step 3Remove the cover from the Mallory distributor byremoving the two screws. Rotate the shaf

Page 3 - FOR MOTORCYCLES

With the Module wired to the coil like it’s ready to run. Take the cap off and position the Module so you can see it. Turn the key on, test voltage on

Plus de documents pour Pour la voiture Mallory-ignition Mallory UNILITE DISTRIBUTOR 576

Voir le document Mallory-ignition Mallory UNILITE DISTRIBUTOR 576 Manuel d'utilisateur

Mallory-ignition Mallory UNILITE DISTRIBUTOR 576 Manuel d'utilisateur (2 pages)

Commentaires sur ces manuels

Pas de commentaire

Mallory-ignition Mallory UNILITE DISTRIBUTOR 576 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Mallory-ignition Mallory UNILITE DISTRIBUTOR 576. Mallory Ignition Mallory UNILITE DISTRIBUTOR 576 User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Pour la voiture Mallory-ignition Mallory UNILITE DISTRIBUTOR 576

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Mallory-ignition Mallory UNILITE DISTRIBUTOR 576