Mallory-ignition Mallory HEI PERFORMANCE COIL 29212_29215 Manuel d'utilisateur télécharger pdf

HEI PERFORMANCE COIL

PART NO. 29212, Effective up to 5,500 RPM

PART NO. 29215, Effective from 4,000 to 7,000 RPM

LIST OF PARTS:

1 HEI Performance Coil

1 Rubber washer

1 Carbon brush and spring

1 Ground strap

4 Self tapping screws

INSTALLATION PROCEDURE

Step 1

Disconnect the battery (–) cable to cut power to the system.

Step 2

Disconnect wire harnesses from the distributor cap. There are more than one.

Remove the distributor cap and check for wear. Replace if necessary.

Step 3

Remove and discard the spark plug wire retainer and coil cover.

Step 4

Notice that the red wire from coil was positioned under the BATT (+) imprint on

the coil cover, and the white or yellow wire from coil was positioned under the

COIL (–) or TACH imprint on the coil cover. Gently lift (pull) each terminal

assembly and wire upward from each cavity in the distributor cap.

Step 5

Remove and discard the four coil mounting screws. Remove and discard the coil.

Step 6

Gently lift (pull) the ground strap upward from its cavity in the distributor cap, and

replace it with the new ground strap. Remove rubber washer and carbon brush

with spring from the distributor cap. Install new carbon brush with spring into the

distributor cap. Coat both sides of new rubber washer with dielectric grease and

install into the distributor cap.

Step 7

Hold the HEI Performance Coil above the distributor cap. Insert terminal

assembly with red wire into the cavity on the distributor cap where previous coil

terminal assembly with red wire had been. Insert terminal assembly with yellow

wire into the cavity on the distributor cap where previous coil terminal assembly

with white or yellow wire had been. Lower into place the HEI Performance Coil

onto the distributor cap. Make sure it is fully seated.

Step 8

Insert the four self tapping screws in the four holes on the top of the HEI

Performance Coil cover. Gently tighten each self tapping screw. Do not over

tighten self tapping screws or distributor cap damage may result.

Step 9

Install the distributor cap. Connect wire harnesses to the distributor cap where

each had been previously.

Step 10

Connect the battery (–) cable.

INSTALLATION INSTRUCTIONS

CARBON BRUSH

GROUND

STRAP

DISTRIBUTOR

CAP

RUBBER

WASHER

YELLOW LEAD

COIL (–)

RED LEAD

BATTERY (+)

SCREWS (4)

BATT (+)

GRD

COIL (–)

MALLORY IS A DIVISION OF THE MR. GASKET PERFORMANCE GROUP

550 MALLORY WAY, CARSON CITY, NV 89701

(775) 882-6600 FAX (775) 887-4326

www.mrgasket.com

FORM 1221

REV. C (10/99)

MADE IN USA

PRINTED IN USA

1 2 3

Résumé du contenu

Page 1 - HEI PERFORMANCE COIL

HEI PERFORMANCE COILPART NO. 29212, Effective up to 5,500 RPMPART NO. 29215, Effective from 4,000 to 7,000 RPMLIST OF PARTS:1 HEI Performance Coil1 Ru

Page 2 - INSTRUCTIONS D’INSTALLATION

BOBINE POUR SYSTÈME D’ALLUMAGE À HAUTE PUISSANCEPIÈCE NO29212, efficace jusqu’à 5 500 tr/min.PIÈCE NO29215, efficace entre 4 000 et 7 000 tr/min.LISTE

Page 3 - BOBINA DE RENDIMIENTO HEI

BOBINA DE RENDIMIENTO HEINO. DE PIEZA 29212, Eficaz hasta 5,500 RPMNO. DE PIEZA 29215, Eficaz de 4,000 a 7,000 RPMLISTA DE PIEZAS:1 Bobina de rendimie

Commentaires sur ces manuels

Pas de commentaire

Mallory-ignition Mallory HEI PERFORMANCE COIL 29212_29215 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Mallory-ignition Mallory HEI PERFORMANCE COIL 29212_29215. Mallory Ignition Mallory HEI PERFORMANCE COIL 29212_29215 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Mallory-ignition Mallory HEI PERFORMANCE COIL 29212_29215